آمار
| تعداد نشریات | 26 |
| تعداد شمارهها | 447 |
| تعداد مقالات | 4,557 |
| تعداد مشاهده مقاله | 5,380,005 |
| تعداد دریافت فایل اصل مقاله | 3,580,078 |
Measuring Some Mechanical Properties of Boxwood and Privet Plants by an Izod Impact Tester | ||
| Biomechanism and Bioenergy Research | ||
| دوره 1، شماره 2، اسفند 2022، صفحه 7-12 اصل مقاله (839.9 K) | ||
| نوع مقاله: Original Research | ||
| شناسه دیجیتال (DOI): 10.22103/bbr.2022.20351.1014 | ||
| نویسندگان | ||
| Mohammad Reza Kamandar* 1؛ Jafar Massah2؛ Farhad Khoshnam1 | ||
| 1Department of Mechanical Engineering of Biosystems, University of Jiroft, Jiroft, Iran | ||
| 2Department of Agrotechnology, College of Abouraihan, University of Tehran, Tehran, Iran | ||
| چکیده | ||
| The information of the impact cutting behavior of plants stalk, play an important role in the design and fabrication of plants cutting equipment. It is difficult to investigate a theoretical method to define cutting properties of plants stalks because the cutting process is complex. Thus, it is necessary to set up an experimental approach to determine cutting parameters for a single stalk. To measure the shear force, shear energy and shear strength of plant stalk, a special impact cutting tester was fabricated. The apparatus included four strain gages and a digital indicator to show the real-time cutting force and requirement cutting energy of plant stalk. To test the apparatus, a series of laboratory tests were conducted to measure the shear force, shear consumption energy and shear strength of stem internodes of two plants stalk like boxwood or box with a scientific name of Buxus (Buxus Sp) and privet with a scientific name of Ligustrum Ovalifolium (Oleaceae Sp) under impact cutting at four loading rates (1, 2, 3 and 4 m/s) and three internodes of stalk (fifth, tenth and fifteenth). At boxwood cutting analysis: the minimum and maximum values of shear consumption energy were obtained as 3.19 J at fifth internode and loading rate: 4 m/s and 19.6 J at fifteenth internode and loading rate: 1 m/s, respectively. The minimum and maximum values of shear strength were obtained as 0.06 MPa at fifth internode and loading rate: 4 m/s and 1.55 MPa at fifteenth internode and loading rate: 1 m/s, respectively. At privet cutting analysis: the minimum and maximum values of shear consumption energy were obtained as 3.95 J at fifth internode and loading rate: 4 m/s and 28.56 J at fifteenth internode and loading rate: 1 m/s, respectively. The minimum and maximum values of shear strength were obtained as 0.2 MPa at fifth internode and loading rate: 4 m/s and 2.50 MPa at fifteenth internode and loading rate: 1 m/s, respectively. | ||
| کلیدواژهها | ||
| Boxwood؛ Privet؛ Impact cutting؛ Shear energy | ||
| مراجع | ||
|
Alizade, MR, Ajdadi, FR and Dabbaghi, A (2011). Cutting energy of rice stem as influenced by internode position and dimensional characteristics of different varieties. Australian Journal of Crop Science., 5, 681-687.
Asae, S (2005b). Moisture relationships of plant-based agricultural products. St. Joseph, Mich. ASAE.
Azadbakht, M, Esmaeilzadeh, E and Esmaeili-Shayan, M (2015). Energy consumption during impact cutting of canola stalk as a function of moisture content and cutting height. Journal of the Saudi Society of Agricultural Sciences, 14, 147-152.
Boydas, MG, Comakli, M, Sayinci, B and Kara, M (2019). Effects of moisture content, internode region, and oblique angle on the mechanical properties of sainfoin stem. Turkish Journal of Agriculture and Forestry, 43, 254-263.
Chattopadhyay, PS and Pandey, KP (2001). Impact cutting behavior of sorghum stalk using a flail -cutter-amathematical model and its experimental verification. Jornal of Agricultural Engineering Research, 78, 369-376.
Dange, AR, Thakare, ST and Bhasharrao, I (2011). Cuttting energy and force as required for pigeon pea stems. Journal of Agricultural Technology., 7, 1485-1493.
Farahat, H and Brooghani, SYA (2016). Design and instrumentation of low velocity drop-weight impact testing machine for estimation of energy absorption capacity in aluminum based composite foam. Modares Mechanical Engineering, 16, 219-228, (in Persian).
Kaewwinud, N, Khokhajaikiat, P and Boonma, N (2017). Effect of moisture and region of cut on cassava stalk properties in biomass applications Res. Agr. Eng. , 63, 23-28.
Konuralp Eliçin, A, Sessiz, A and Göksel Pekitkan, F (2019). Effect of Various Knife Type, Cutting Angle and Speed on Cutting Force and Energy of Grape Cane. European Journal of Science and Technology, 15, 519-525.
Mathanker, SK, Grift, TE and Hansen, AC (2015). Effect of blade oblique angle and cutting speed on cutting energy for energycane stems. Biosystems Engineering., 133, 64-70.
Mcrandal, DM and Mcnulty, PB (1978). Impact cutting behavior of forage crops-mathematical models and laboratory tests. j. Agr. Engng Res., 23, 313-328.
Mohsenin, NN (1963). Physical properties of plant and animal materials. Gordon and Breach Science Publishers, New York.
O' Degherty, MJ, Hubert, JA, Dyson, J and Marshall, CJ (1995). A study of the physical and mechanical properties of wheat straw. Jornal of Agricultural Engineering Research, 62, 133-142.
Prasad, J and Gupta, CP (1975). Mechanical properties of maize stalk as related to harvesting. . Jornal of Agricultural Engineering Research, 20, 79-87.
Shahbazi, F and Nazari Galedar, M (2012). Bending and shearing properties of safflower stalk. J. Agr. Sci, 14, 743-754.
Sitkei, G (1986). Mechanics of agricultural materials. Elsevier Science Publishers, 445-450.
Tabatabaee Koloor, R and Borgheie, A (2006). Measuring the static and dynamic cutting force of stems for Iranian rice varieties. Journal of Agricultural Science and Technology, 8, 193-198.
Taghijarah, H, Ahmadi, H, Ghahderijani, M and Tavakoli, M (2011). Shearing characteristics of sugar cane stalks as a function of the rate of the force. Australian Journal of Crop Science., 5, 630-634.
Taghinezhad, J, Alimardani, R and Jafari, A (2013). Effect of moisture content and dimensional size on the shearing characteristics of sugarcane stalks. Journal of Agricultural Technology., 9, 281-294.
Yiljep, YD and Mohammed, US (2005). Effect of knife velocity on cutting energy and efficiency during impact cutting of sorghum stalk. Agicultural Engineering International: the CIGR Ejornal. Manuscript PM 05 004., VII. | ||
|
آمار تعداد مشاهده مقاله: 154 تعداد دریافت فایل اصل مقاله: 200 |
||